cloudstack-users mailing list archives

Site index · List index
Message view « Date » · « Thread »
Top « Date » · « Thread »
From Abdul Rasool <rasool...@gmail.com>
Subject Re: Fwd: Guest VM with Multiple Networks on single VR (Virtual Router)
Date Tue, 14 Oct 2014 12:04:49 GMT
Hi Kirk,

I think we both are not on the same page, could you please go through my
below emails and let me know is my question is clear to you. if so please
help to configure this scenario.

Thanks in advance.
AR

On Tue, Oct 14, 2014 at 12:56 AM, Kirk Kosinski <kirkkosinski@gmail.com>
wrote:

> Hi, all VM configuration needs to be done in CloudStack, otherwise it
> will be undone by CloudStack under various common circumstance (reboot,
> stop/start, etc.).
>
> Best regards,
> Kirk
>
> On 10/13/2014 04:03 AM, Abdul Rasool wrote:
> > Hi Kirk
> >
> > Thanks for your reply,
> >
> > adding to some more points on the same case I want to add additional
> > physical NIC to VM without mention IPs and service offering from
> cloudstack
> > is that possible ?. in my case I have 1 VM which has public NIC and need
> > one more additional physical NIC for internal use. on the WAN side every
> > thing is working as expected in the same VM I would need to add one more
> > physical NIC which I need to manually configure IPs in different range
> > apart from the default CIDR.(Eg - connecting to different network over
> > MPLS) meaning one guest VM will have two network one towards to public
> with
> > default CIDR and other network towards to MPLS on different IP range, is
> > that possible if so could you please assist me on this.
> >
> > Thanks
> > AR
> >
> > On Sat, Oct 11, 2014 at 9:46 AM, Kirk Kosinski <kirkkosinski@gmail.com>
> > wrote:
> >
> >> Hi, as I said before you may still be required to input an IP range when
> >> creating the network, but it won't be used if DHCP is disabled for the
> >> network.  So just input any IP range when creating the network and then
> >> configure the desired IP address in the VM.
> >>
> >> Best regards,
> >> Kirk
> >>
> >>
> >> On 10/10/2014 11:41 AM, Abdul Rasool wrote:
> >>> Hi Kirk
> >>>
> >>> Thanks for your response
> >>> I have tried creating service offering  without dhcp but while creating
> >>> guest network its forcing me to mention IP range. My requirement  is
> >> that i
> >>> will get only 1 IP from each branch network that I have to configure in
> >>> guest VM directly. In the branch network switch is created with
> multiple
> >> L2
> >>> vlans. Please guide me how to setup this network.
> >>>
> >>> I hope you have seen my model network diagram which  i have uploaded in
> >>> google drive.
> >>>
> >>> Thx in advance
> >>> AR.
> >>>  On 10 Oct 2014 22:42, "Kirk Kosinski" <kirkkosinski@gmail.com> wrote:
> >>>
> >>>> Hi, if you don't want DHCP for your branch office network you need to
> >>>> create a Network Offering without DHCP and select that offering when
> >>>> adding the network in CloudStack.  You may still be required to input
> an
> >>>> IP range when creating the network, but CloudStack won't be able to
> >>>> assign the IPs with DHCP disabled.
> >>>>
> >>>> Best regards,
> >>>> Kirk
> >>>>
> >>>> On 10/10/2014 05:06 AM, Abdul Rasool wrote:
> >>>>> Hi All,
> >>>>>
> >>>>>
> >>>>>
> >>>>> I am new to Cloudstack I would required your help to achieve my
> >> advanced
> >>>>> networking configuration. right now I am using CS-4.4.0 management
> >> server
> >>>>> with Mysql DB on it. I have 2 computing server with multiple NICs
to
> >> test
> >>>>> my environment. As per the study guide I could able to test all
the
> >>>>> functionality except my topology point view. Basically I would need
> my
> >>>>> guest VM to have 2 Physical NICs one towards to Internet (eth0)
& VM
> to
> >>>> VM
> >>>>> communication and other Physical NIC (eth1) for my branch office
> >>>>> connectivity without configuring gateway on the interface. I will
> >>>> manually
> >>>>> add route on the VM. I have tried all the possibility ways with
my
> poor
> >>>>> knowledge on the CS I could not able to add guest network without
> >>>>> mentioning IP range on the UI also cloudmonkey.  I want to configure
> >> IPs
> >>>> on
> >>>>> the eth1 nic (Branch network) manually without getting IPs from
DHCP,
> >>>> could
> >>>>> someone please guide me on this.  We are already running similar
> setup
> >> on
> >>>>> VMware I hope this can be done on cloudstack as well.
> >>>>>
> >>>>>
> >>>>>
> >>>>> Configuration details.
> >>>>>
> >>>>>
> >>>>>
> >>>>> Management Server / computing server is running on Ubuntu detail
are
> >>>> below.
> >>>>>
> >>>>>
> >>>>>
> >>>>> Distributor ID: Ubuntu
> >>>>>
> >>>>> Description: Ubuntu 12.04.5 LTS
> >>>>>
> >>>>> Release: 12.04
> >>>>>
> >>>>> Codename: precise
> >>>>>
> >>>>> Virtualization is on = KVM
> >>>>>
> >>>>> Guest VM OS = Windows -7, CentOS
> >>>>>
> >>>>>
> >>>>>
> >>>>> I have attached detailed diagram for your better understanding,
> please
> >>>> help
> >>>>> me to configure my scenario.
> >>>>>
> >>>>>
> >>>>> Please find this below link for network diagram.
> >>>>>
> >>>>>
> >>>>
> >>
> https://drive.google.com/file/d/0B_WdtmbCAFl4bW91d1VPajFzdkk/view?usp=sharing
> >>>>>
> >>>>>
> >>>>>
> >>>>> Thanks in Advance.
> >>>>>
> >>>>>
> >>>>>
> >>>>> Abdul Rasool.
> >>>>>
> >>>>> +91 98865 18767
> >>>>>
> >>>>
> >>>
> >>
> >
>

Mime
  • Unnamed multipart/alternative (inline, None, 0 bytes)
View raw message